The AP-N-3 ventilation control unit is a compact ventilation control centre for 24 V DC drives up to 3 A with a 230 V AC input voltage. (not in synchronised operation) It is ideal for opening and closing 24 V DC drives. It is designed for over 10,000 ventilation cycles. Robust sheet steel housing for greater safety The control unit is housed in a robust sheet steel housing. This means that the electronics are optimally protected against external influences. Advantages at a glance: for opening and closing 24 V DC drives designed for over 10,000 ventilation cycles versatile in use in a robust sheet steel housing

The AP-N-6 ventilation control unit is a compact ventilation control centre for 24 V DC drives up to 6 A with a 230 V AC input voltage (not in synchronous operation). It is ideal for opening and closing 24 V DC drives. It is designed for over 10,000 ventilation cycles. Robust sheet steel housing for greater safety The control unit is housed in a robust sheet steel housing. This means that the electronics are optimally protected against external influences. Advantages at a glance: for opening and closing 24 V DC drives designed for over 10,000 ventilation cycles versatile in use in a robust sheet steel housing

The AP-NS-3 ventilation control unit is a compact ventilation control centre for 24 V DC drives up to 3 A with a 230 V AC input voltage (also in synchronous operation). It is ideal for opening and closing 24 V DC drives. It is designed for over 10,000 ventilation cycles. Robust sheet steel housing for greater safety The control unit is housed in a robust sheet steel housing. This means that the electronics are optimally protected against external influences. Advantages at a glance: for opening and closing 24 V DC drives can be used for synchronised operation designed for over 10,000 ventilation cycles versatile in use in a robust sheet steel housing

The AP-NS-6 ventilation control unit is a compact ventilation control centre for 24 V DC drives up to 6 A with a 230 V AC input voltage (also in synchronous operation). It is ideal for opening and closing 24 V DC drives. It is designed for over 10,000 ventilation cycles. Robust sheet steel housing for greater safety The control unit is housed in a robust sheet steel housing. This means that the electronics are optimally protected against external influences. Advantages at a glance: for opening and closing 24 V DC drives can be used for synchronised operation designed for over 10,000 ventilation cycles versatile in use in a robust sheet steel housing

The SHEV-3-AP is the surface-mounted version of the SHEV-3 compact control centre and is used for smoke extraction in stairwells. It is housed in a sheet steel casing. The compact control centre has an output current of 3 A. The SHEV compact control centre is a compact device designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system), which are also monitored. Designed for daily ventilation applications, corresponding components can be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. Safe control thanks to emergency power supply In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV-3-AP compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for triggering devices Connections for external components Emergency power supply for at least 72 hours

The SHEV-6-AP is the surface-mounted version of the SHEV-6 compact control centre and is used for smoke extraction in stairwells. It is housed in a sheet steel casing. The compact control centre has an output current of 6 A. The SHEV compact control centre is a compact device designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system), which are also monitored. Designed for daily ventilation applications, corresponding components can be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. Safe control thanks to emergency power supply In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV-6-AP compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for triggering devices Connections for external components Emergency power supply for at least 72 hours

The SHEV 602 is a version of the SHEV 3 AP compact control centre in the SHEV area. The SHEV 602 consists of two SHEV-3 with coupled WTS connection and a central feed-in point and is installed in a steel wall-mounted cabinet with a full door. The compact control centre has an output current of 3 A per SHEV-3. The SHEV compact control centre is a compact device designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system), which are also monitored. Designed for daily ventilation applications, corresponding components can be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. Safe control thanks to emergency power supply In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV-602 compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for triggering devices Connections for external components Emergency power supply for at least 72 hours

The SHEV-3-HE-081-RE is the variant of the SHEV-3 compact control centre with integrated manual control unit / auxiliary control unit and membrane keypad for ventilation control. It is used for smoke extraction in stairwells. It is housed in a sheet steel casing. The compact control centre has an output current of 3 A. The SHEV compact control centre is a compact device designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system), which are also monitored. Designed for daily ventilation applications, corresponding components can be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. Safe control thanks to emergency power supply In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV-3-HE-082-RE compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for triggering devices Connections for external components Emergency power supply for at least 72 hours with built-in manual release device / auxiliary control unit HE-082 in orange with high-quality membrane keypad for ventilation control OPEN / CLOSE / STOP

The SHEV-3-HE-082-RE is the variant of the SHEV-3 compact control centre with built-in manual control unit / main control panel and membrane keypad for ventilation control. It is used for smoke extraction in stairwells. It is housed in a sheet steel casing. The compact control centre has an output current of 3 A. The SHEV compact control centre is a compact device designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system), which are also monitored. Designed for daily ventilation applications, corresponding components can be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. Safe control thanks to emergency power supply In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV-3-HE-082-RE compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for triggering devices Connections for external components Emergency power supply for at least 72 hours with built-in manual release device / main control panel HE-082 in orange with high-quality membrane keypad for ventilation control OPEN / CLOSE / STOP

The Shaft Panel SP-300 is a compact central system in the SHEV area. Smoke extraction takes place through a shaft in the building that runs vertically across all floors. A shaft system consists of an HSP (Head of Shaft Panel) with a smoke extraction flap at the end of the shaft and an SP (Shaft Panel) on each floor, which in turn controls a smoke extraction flap. In the event of a SHEVS alarm (triggering), the smoke is discharged upwards via the shaft by opening the smoke extraction flaps in the shaft in a targeted manner. The system can be supplemented by a staircase control unit (Stair Panel). An additional circuit board is installed especially for this product, which allows a reduced number of cores in the cable routing for the manual release devices. The signals for SHEV, reset and the alarm, OK and fault indicators can be forwarded using only 3 wires. This makes the SP-300 / 600 particularly suitable for replacing and refurbishing old buildings. Often, only supply lines with fewer wires are available on site. Safe housing for components The SP-300 electrical control unit is housed in a plastic casing and contains the power supply, emergency power supply and all the control and regulation electronics for operating 24 V DC drives for windows and smoke extraction flaps. The compact control centre controls the connected drives in the event of a fire and can also be used for daily ventilation. The ventilation function also serves as a regular function check of the Shaft system. Safety thanks to 72 hours of emergency power In the event of a power failure, the emergency power supply ensures that the Shaft system continues to function for at least 72 hours. The connection cables for the SHE button (HE manual control unit), smoke detector (RM), fire alarm system (FACS) and drives are monitored. The housing can be sealed. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. Advantages at a glance: Can be supplemented with staircase control sealable plastic housing Energy supply, emergency power supply, control and regulation electronics included Emergency power supply for at least 72 hours

The Shaft Panel SP-300-AP is a compact central system in the SHEV area with an output current of 3 A. Smoke extraction takes place through a shaft in the building that runs vertically across all floors. A shaft system consists of one HSP (Head of Shaft Panel) with a smoke extraction damper at the end of the shaft and one SP (Shaft Panel) on each floor, which in turn control a smoke extraction damper. In the event of a SHEVS alarm (triggering), the smoke is discharged upwards via the shaft by opening the smoke extraction flaps in the shaft in a targeted manner. The system can be supplemented by a staircase control unit (Stair Panel). An additional circuit board is installed especially for this product, which allows a reduced number of wires in the cable routing for the manual release devices. The signals for SHEV, reset and the alarm, OK and fault indicators can be forwarded using just three wires. This makes the SP-300-AP particularly suitable for replacing and refurbishing old buildings. Often, only on-site supply lines with fewer cores are available there. Secure housing for components The SP-300-AP electrical control unit is housed in a sheet steel housing and thus offers greater protection for the electronics. It contains the power supply, emergency power supply and all the control and regulation electronics for operating 24 V DC drives for windows and smoke extraction flaps. The compact control centre controls the connected drives in the event of a fire and can also be used for daily ventilation. The ventilation function also serves as a regular function check of the Shaft system. The control unit is surface-mounted. Safety thanks to 72 hours of emergency power In the event of a power failure, the emergency power supply ensures that the Shaft system continues to function for at least 72 hours. The connection cables for the SHE button (HE manual control unit), smoke detector (RM), fire alarm system (FACS) and drives are monitored. The housing can be sealed. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. Advantages at a glance: Can be supplemented with staircase control Suitable for replacement and use in old buildings Surface-mounted installation powder-coated sheet steel housing Energy supply, emergency power supply, control and regulation electronics included Emergency power supply for at least 72 hours

The Shaft Panel SP-600 is a compact central system in the SHEV area that controls the connected drives in the event of a fire and for daily ventilation. Smoke extraction takes place through a shaft in the building that runs vertically across all floors. A shaft system consists of an HSP (Head of Shaft Panel) with a smoke extraction flap at the end of the shaft and an SP (Shaft Panel) on each floor, which in turn controls a smoke extraction flap. In the event of a SHEVS alarm (triggering), the smoke is discharged upwards via the shaft by opening the smoke extraction flaps in the shaft in a targeted manner. The system can be supplemented by a staircase control unit (Stair Panel). An additional circuit board is installed especially for this product, which allows a reduced number of cores in the cable routing for the manual release devices. The signals for SHEV, reset and the alarm, OK and fault indicators can be forwarded using only 3 wires. This makes the SP-300 / 600 particularly suitable for replacing and refurbishing old buildings. Often, only supply lines with fewer wires are available on site. Safe housing for components The SP-300 electrical control unit is housed in a plastic casing and contains the power supply, emergency power supply and all the control and regulation electronics for operating 24 V DC drives for windows and smoke extraction flaps. The compact control centre controls the connected drives in the event of a fire and can also be used for daily ventilation. The ventilation function also serves as a regular function check of the Shaft system. Safety thanks to 72 hours of emergency power In the event of a power failure, the emergency power supply ensures that the Shaft system continues to function for at least 72 hours. The connection cables for the SHE button (HE manual control unit), smoke detector (RM), fire alarm system (FACS) and drives are monitored. The housing can be sealed. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. Advantages at a glance: Can be supplemented with staircase control sealable plastic housing Energy supply, emergency power supply, control and regulation electronics included Emergency power supply for at least 72 hours

The Shaft Panel SP-600-AP is a compact central system in the SHEV area with an output current of 6 A. Smoke extraction takes place through a shaft in the building that runs vertically across all floors. A shaft system consists of one HSP (Head of Shaft Panel) with a smoke extraction damper at the end of the shaft and one SP (Shaft Panel) on each floor, which in turn control a smoke extraction damper. In the event of a SHEVS alarm (triggering), the smoke is discharged upwards via the shaft by opening the smoke extraction flaps in the shaft in a targeted manner. The system can be supplemented by a staircase control unit (Stair Panel). An additional circuit board is installed especially for this product, which allows a reduced number of wires in the cable routing for the manual release devices. The signals for SHEV, reset and the alarm, OK and fault indicators can be forwarded using just three wires. This makes the SP-300-AP particularly suitable for replacing and refurbishing old buildings. Often, only on-site supply lines with fewer cores are available there. Secure housing for components The SP-600-AP electrical control unit is housed in a sheet steel housing and thus offers greater protection for the electronics. It contains the power supply, emergency power supply and all the control and regulation electronics for operating 24 V DC drives for windows and smoke extraction flaps. The compact control centre controls the connected drives in the event of a fire and can also be used for daily ventilation. The ventilation function also serves as a regular function check of the Shaft system. The control unit is surface-mounted. Safety thanks to 72 hours of emergency power In the event of a power failure, the emergency power supply ensures that the Shaft system continues to function for at least 72 hours. The connection cables for the SHE button (HE manual control unit), smoke detector (RM), fire alarm system (FACS) and drives are monitored. The housing can be sealed. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. Advantages at a glance: Can be supplemented with staircase control Suitable for replacement and use in old buildings Surface mounting powder-coated sheet steel housing Energy supply, emergency power supply, control and regulation electronics included Emergency power supply for at least 72 hours

Accessories NC-2406-LÖ for the SHEV Spare NiCad battery, with solder tabs for self-installation 24 V DC / 0.6 Ah / loose for self-installation in electrical control units of type RZ 040, RZ 140, RZ 272, ES 251 and ES 601

Accessories NC-2406-TK for the SHEV Replacement battery for previous and current compact control centres NiCad battery, 24 V DC / 0.6 Ah/ loose suitable for electrical control units of type ES 3/1, RZ 4/1, ES 6/1 in TK housing and all ESM 6 Amp

NC-2412 accessories for the SHEV NiCad battery for electrical control units of type ESM-T/X, ESM 12 Amp, ESV 251 24 V DC / 1.2 Ah / loose

Accessories SHEV-3-AP Replacement battery / battery pack 2.3 Ah for the SHEV Replacement battery for previous and current compact control centres for use in sheet steel surface-mounted housing

Accessories SHEV-3(6) Replacement battery / battery pack 2.3 Ah for the SHEV Replacement battery for the SHEV on a carrier plate

The SHEV 2 ECO electrical control unit is a compact device in a plastic housing. It contains the power supply, emergency power supply and all the control and regulation electronics for operating 24 V DC drives for windows and smoke extraction flaps. The output current is 2 A. Compact central system for smoke extraction The SHEV 2 ECO is a compact central system for smoke extraction. It is housed as a compact module in a single-board system in a surface-mounted housing. The SHEV 2 ECO is primarily used to equip systems for smoke extraction in stairwells. The SHEV signal can be reset on the manual control unit. If the RESET button is pressed for the first time, only the SHEV message is reset. If there is a SHEV alarm on signalling line 1 or 2 at this time, this message is suppressed for 3 seconds when the RESET button is pressed and signalling lines 1 and 2 are also switched off for the same time. If the RESET button is pressed a second time, the smoke extraction flaps are closed. In addition to the manual control unit, the SHEV-2-ECO also has connection terminals for smoke detectors and a ventilation button for natural ventilation. SHEV-2-ECO at a glance: Compact control centre for smoke extraction in stairwells Energy supply, emergency power supply, control and regulation electronics included Surface-mounted plastic housing SHEV signalling can be reset on the manual control unit

The SHEV 2 HM electrical control unit is a compact device in a plastic housing. Unlike the short-time operation of SHEV drives, holding magnets require constant control. In the version for holding magnets, the SHEV-2-HM offers a continuous load current of 2 amps. The SHEV-2-HM contains the power supply, emergency power supply and the entire control electronics for operating 24 V DC holding magnets. In the event of a power failure, the emergency power supply ensures that the SHEV system continues to function for at least 30 minutes. The connection cables for SHEV buttons (manual control devices), smoke detectors and fire alarm system (FACP) are monitored. The housing can be sealed. In conjunction with the EAP-HM locking fitting (0.125 A each), up to 16 holding magnets can be operated in parallel. Advantages at a glance: Designed for use with holding magnets Energy supply, emergency power supply, control electronics included Emergency power holding time of at least 30 minutes Monitoring of the connection cables for SHEV button, smoke detector and BMZ sealable housing

The SHEV 3 compact control centre is a compact device with an output current of 3 A, designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, e.g. windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV compact control centre is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system). Designed for daily ventilation applications, corresponding components can also be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. The connection cables for SHEV buttons (manual control devices), smoke detectors, fire alarm system (FACS) and drives are monitored. Emergency power supply for 72 hours In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells for ventilation/smoke extraction Connections for release devices Connections for external components Emergency power supply for at least 72 hours

The SHEV compact control centre is a compact device with an output current of 6 A, designed in accordance with European specifications. The control unit contains a primary and secondary power supply as well as the entire control and regulation technology for operating 24 V DC drives for building openings, e.g. windows and smoke extraction flaps. The compact control centre controls the drives in the event of a fire and for daily ventilation. Special ventilation functions (gap ventilation, dead man's function, automatic ventilation) can be freely and individually programmed by the user. The ventilation function is also a daily function check of the smoke evacuation centre. The manual or automatic triggering of the smoke and heat extraction system activates servomotors or fittings via pole application, which release the openings in the wall or roof area intended for smoke extraction. Compact control centre for SHEV and NSHEV The SHEV compact control centre is specially designed for SHEV use in stairwells and for NSHEV and offers all the necessary connections for triggering devices (manual control unit, smoke detector, fire alarm system). Designed for daily ventilation applications, corresponding components can also be connected: Wind/rain detectors, fan buttons, timers and higher-level controls. The connection cables for SHEV buttons (manual control devices), smoke detectors, fire alarm system (FACS) and drives are monitored. Emergency power supply for 72 hours In the event of a power failure, the emergency power supply ensures the function of the SHEV system for at least 72 hours. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. The SHEV compact control centre is CE certified in accordance with DIN EN 12101-10 and tested in accordance with ISO 21927-9. Advantages at a glance: contains primary and secondary energy supply as well as the entire control and regulation technology special ventilation functions can be freely and individually programmed daily function check of the SHEV system ideal for use in stairwells contains all the necessary connections for triggering devices Connections for external components Emergency power supply for at least 72 hours

NC-2406 accessories for the SHEV Replacement battery for current and previous compact control centres NiCad battery, 24 V DC / 0.6 Ah / loose Portrait format in CI-D housing suitable for electrical control units built before 1994

The VENT-3 electric ventilation control unit is a compact device in a metal housing. It contains the power supply and all the control and regulation electronics for operating 24 V DC drives. The VENT-3 controls the connected drives for daily ventilation. The VENT-3 can be operated without accessories via the membrane keypad integrated in the cover. It is also possible to connect an additional external ventilation button and a thermostat using a THM-200 (not included). By connecting a rain or wind/rain detector, the VENT-3 reacts automatically to undesirable environmental influences. The following functions can be set via the DIP switches on the circuit board: permanent activation of normally closed units after the ventilation button is touched, dead man's function, programmable stroke limitation and automatic "CLOSED" ventilation. The degree of automation can be set by the user. The SIMON LINK parameterisation and diagnostics software allows product-specific settings to be changed and maintenance and diagnostics work to be carried out. Connected via Plug & Play, the software immediately accesses the device. Changes to the device settings and maintenance or diagnostic work can be carried out directly on site without any loss of time. Advantages at a glance: Operation of the control unit via integrated membrane keypad Expansion of the control system using external components Ideal adaptation of the ventilation in the building Specific product settings via SIMON LINK